You can control access to the management services of Sophos Firewall from custom and default zones using the local service ACL (Access Control List).
Local services are management services specific to the internal functioning of Sophos Firewall, such as web admin and CLI consoles, and authentication services. You can allow or block access to local services from Administration > Device access.
- Select the checkboxes to allow access to these services from different zones. See Access to local services from zones.
- To only allow specific hosts and networks to access the services, scroll down to Local service ACL exception rule, and click Add.
Local service ACL: How device access works
The following conditions apply to local services:
- You can't control traffic to these services using firewall rules. You can only do so from Administration > Device access.
- For custom zones, you can also allow or block access from Network > Zones.
- To access a local service that shares a host's subnet, zone, or interface, you must select the zone. For example, to access the DNS service from the LAN zone when Sophos Firewall is the DNS server, you must select LAN for DNS.
- The default ports are used to provide access to these services, and the destination IP address is set to Sophos Firewall.
- You can change the default ports of some services, such as SSL VPN and user portal, from the corresponding settings pages. If you change the ports, we recommend not using the SSL VPN port for other services. It allows access to the services from zones that you turned off here.
Here are the default settings for the local service access control list:
Administrative services and user portal: We do not recommend allowing access to the web admin console (HTTPS), CLI console (SSH), and the user portal from the WAN zone or over the SSL VPN port. If you must give access, we recommend using the best practices listed in the table in this section.
SSL VPN port: By default, all management services use unique ports. SSL VPN is set to TCP port 8443.
If you manually change the default ports, we strongly recommend that you use a unique port for each service. Using a unique port ensures that services are not exposed to the WAN zone even after you turn off access. Example: Don't use port 443 for both the user portal and SSL VPN. If you do, the user portal will remain accessible from the WAN zone when you turn off WAN access from this page.
|Consoles||Secure access from WAN|
|Web admin console||Use Sophos Central. For more details, go to Sophos Central. |
|CLI console||Create a local service ACL exception rule allowing specific source IP addresses to access the console from the WAN zone. |
|User portal||For secure access from external networks, use VPNs and follow these best practices: |
Secure access based on user accounts:
Default admin password settings
The factory configuration of Sophos Firewall carries a default super administrator with the following credentials:
You can use these to sign in to the web admin console and the CLI. You must change the default password when you configure Sophos Firewall for the first time.
Sophos Firewall offers stronger password protection for the default super administrator. To benefit from the protection, you must change the password if you're upgrading from 18.0 MR3 or earlier or 17.5 MR14. This is a one-time change.
Store the current password in a secure location. If you move to an earlier firmware version that uses the current password, you'll need it to sign in.
Multi-factor authentication (MFA) for the default admin
You can set up MFA based on hardware or software tokens for the default administrator.
- Turn on MFA for default admin and click Apply.
Select a token method and click Next:
Configure a hardware token:
- Enter the key the device manufacturer provides.
- Enter the timestep that matches the value configured in the hardware token.
Click Next and enter the default admin's password followed by the passcode shown on the hardware token.
Click Validate and click Apply.
Generate a software token:
- Install an authenticator app on your mobile device and scan the QR code.
- Enter your password followed by the passcode in the following format:
- Click Validate and click Apply.
If you apply MFA for the default admin, make sure you store the additional passcodes in a secure location, such as a password manager. See Generate passcodes on the firewall.
If you don't, you risk losing access if the default admin loses the mobile device that has the authenticator app.
If you have an existing hardware or software token and are only turning on MFA, choose from the following options and follow the instructions:
- Use an existing token: Enter the password followed by the passcode.
- Generate a software token: Scan the QR code using an authenticator app.
Public key authentication for admin
You can use public keys for secure access to the CLI. You can add, edit, or delete SSH keys.
- Turn on Enable authentication to allow secure access to the CLI using an SSH key.
- To generate a public-private key pair, use SSH tools (example: PuTTYgen).
- Go to Administration > Device access, scroll down to Public key authentication for admin, and add the public key.
Share the private key with the administrator who needs to access the CLI.
To access the CLI, the administrator must enter the private key in the SSH tool (example: PuTTY).
You can also use this method to give secure access to Sophos Support for troubleshooting purposes.